J-Link 19-Pin Cortex-M Adapter (8.06.00)
19-Pin Cortex-M Adapter
The J-Link 19-Pin Cortex-M Adapter converts the 20-pin, 0.1 inch standard connector to a 19-pin, 0.05 inch Cortex-M connector. Includes a Cortex-M 19-pin cable.
J-Link 9-Pin Cortex-M Adapter (8.06.02)
9-Pin Cortex-M Adapter
The J-Link 9-Pin Cortex-M Adapter converts the 20-pin, 0.1 inch standard connector to a 9-pin, 0.05 inch Cortex-M connector. Includes a Cortex-M 9-pin cable.
J-Link RX Adapter (8.06.01)
14-Pin Renesas RX Adapter
The J-Link RX Adapter converts the 20 pin, 0.1 inch standard connector to a 14 pin Renesas connector. Includes the necessary cable.
JTAG Isolator (8.07.00)
JTAG Electrical Isolator
The J-Link JTAG Isolator can be connected between the J-Link / Flasher and the target hardware to provide electrical isolation.
J-Link 14-Pin TI Adapter (8.06.03)
14-Pin TI Adapter
The J-Link 14-Pin TI Adapter converts the 20-pin, 0.1 inch standard connector to a 14-pin, 0.1 inch Texas Instruments connector. Includes a 14-pin TI cable.
J-Link 10-pin Needle Adapter (8.06.04)
20-Pin to 10-Pin Needle Adapter
The 20-Pin to 10-Pin Needle Adapter converts the 20-pin, 0.1 inch standard connector to a 10-pin, 0.05 inch needle pattern.
10-Pin Needle Adapter (8.06.05)
10-Pin to 10-Pin Needle Adapter
The 10-Pin to 10-Pin Needle Adapter converts the 10-pin, 0.1 inch standard connector to a 10-pin, 0.05 inch needle pattern. Does NOT include 20-Pin to 10-Pin Adapter Board.
J-Link TI-CTI-20 Adapter (8.06.06)
J-Link Texas Instruments CTI-20 Adapter
The 20-Pin to 20-Pin CTI Adapter converts the 20-Pin, 0.1 inch standard connector to a 20-Pin TI CTI connection.
SWD Isolator (8.07.01)
SWD Electrical Isolator
The J-Link SWD Isolator can be connected between the J-Link / Flasher and the target hardware to provide electrical isolation.
J-Link 2mm Adapter (8.06.11)
2mm Adapter
The J-Link 2mm Adapter converts the 20-pin, 0.1 inch standard connector to a 20-pin, 2mm connector.
J-Link Microchip Adapter (8.06.09)
J-Link Microchip Adapter
The J-Link Microchip Adapter converts the standard J-Link 20-pin 0.1 inch target connector to the Microchip RJ11 modular debug connector. Includes 6-pin RJ11 modular connector cable.
J-Link RX FINE Adapter (8.06.10)
Renesas RX FINE Adapter
The J-Link RX FINE Adapter converts the 20-pin, 0.1 inch standard connector to a 14-pin, 0.1 inch RX FINE connector. Includes the necessary cable.
J-Link Signal Smoothing Adapter (8.06.12)
Signal Smoothing Adapter
The J-Link Signal Smoothing Adapter can be inserted between the J-Link debug probe and the debug target to
overcome signal integrity issues.
J-Link Measurement+Patch Adapter (8.06.13)
J-Link Measurement+Patch Adapter
The J-Link Measurement+Patch Adapter provides test points for all
debug signals to allow easy access for test probes, and allows customized wiring between
J-Link and targets that do not provide a standard debug connector.
SEGGER Intel FPGA Adapter (8.06.15)
SEGGER Intel FPGA Adapter
The SEGGER Intel FPGA Adapter (formerly referred to as the J-Link Altera Adapter) converts the 20-pin, 0.1 inch pitch standard J-Link connector to a 10-pin Intel FPGA JTAG connector providing debug access to FPGA based MCU cores like the dual core ARM Cortex-A9 in the Cyclone V devices.
J-Link 6-pin Needle Adapter (8.06.16)
20-Pin to 6-Pin Needle Adapter
The 20-Pin to 6-Pin Needle Adapter converts the 20-pin, 0.1 inch standard connector to a 6-pin, 0.05 inch needle pattern.
J-Link Supply Adapter (8.06.14)
Supply Adapter
The J-Link Supply Adapter provides a fixed I/O voltage level for VTRef. It eliminates the need to connect VTRef (pin1 on the standard J-Link interface) to the target.
USB Isolator (8.07.02)
USB Electrical Isolator
The J-Link USB Isolator can be connected between the J-Link / Flasher and the host PC to provide electrical isolation.
J-Link Target Supply Adapter (8.06.18)
Target Supply Adapter
The J-Link Supply Adapter provides a default voltage of 3.3V to power the target using pin 19. The voltage can be adjusted by replacing resistors.
J-Link Xilinx Adapter (8.06.19)
Xilinx Adapter
The J-Link Xilinx Adapter converts the 20-pin, 0.1 inch pitch standard J-Link connector to a 14-pin 2mm pitch connector.
RL78 14-Pin Programming Adapter (8.06.20)
RL78 Programming Adapter
The RL78 Programming Adapter converts the 20-pin, 0.1 inch pitch standard J-Link connector to a 14-pin, E1 connector. Includes 14 pin ribbon cable.
J-Trace Mictor 38 Adapter (8.06.21)
J-Trace Mictor 38 Adapter
Adapts from 20-pin .05" Cortex trace connector to 38 pin Mictor connector. The pin out follows the single target connector pin out specification as defined in the ARM ETM Architecture Specification.