J-Link 19-Pin Cortex-M Adapter (8.06.00)
19-Pin Cortex-M Adapter
The J-Link 19-Pin Cortex-M Adapter converts the 20-pin, 0.1 inch standard connector to a 19-pin, 0.05 inch Cortex-M connector. Includes a Cortex-M 19-pin cable.
J-Link 9-Pin Cortex-M Adapter (8.06.02)
9-Pin Cortex-M Adapter
The J-Link 9-Pin Cortex-M Adapter converts the 20-pin, 0.1 inch standard connector to a 9-pin, 0.05 inch Cortex-M connector. Includes a Cortex-M 9-pin cable.
J-Link RX Adapter (8.06.01)
14-Pin Renesas RX Adapter
The J-Link RX Adapter converts the 20 pin, 0.1 inch standard connector to a 14 pin Renesas connector. Includes the necessary cable.
JTAG Isolator (8.07.00)
JTAG Electrical Isolator
The J-Link JTAG Isolator can be connected between the J-Link / Flasher and the target hardware to provide electrical isolation.
J-Link 14-Pin TI Adapter (8.06.03)
14-Pin TI Adapter
The J-Link 14-Pin TI Adapter converts the 20-pin, 0.1 inch standard connector to a 14-pin, 0.1 inch Texas Instruments connector. Includes a 14-pin TI cable.
J-Link 10-pin Needle Adapter (8.06.04)
20-Pin to 10-Pin Needle Adapter
The 20-Pin to 10-Pin Needle Adapter converts the 20-pin, 0.1 inch standard connector to a 10-pin, 0.05 inch needle pattern.
10-Pin Needle Adapter (8.06.05)
10-Pin to 10-Pin Needle Adapter
The 10-Pin to 10-Pin Needle Adapter converts the 10-pin, 0.1 inch standard connector to a 10-pin, 0.05 inch needle pattern. Does NOT include 20-Pin to 10-Pin Adapter Board.
J-Link TI-CTI-20 Adapter (8.06.06)
J-Link Texas Instruments CTI-20 Adapter
The 20-Pin to 20-Pin CTI Adapter converts the 20-Pin, 0.1 inch standard connector to a 20-Pin TI CTI connection.
SWD Isolator (8.07.01)
SWD Electrical Isolator
The J-Link SWD Isolator can be connected between the J-Link / Flasher and the target hardware to provide electrical isolation.
J-Link 2mm Adapter (8.06.11)
2mm Adapter
The J-Link 2mm Adapter converts the 20-pin, 0.1 inch standard connector to a 20-pin, 2mm connector.
J-Link Microchip Adapter (8.06.09)
J-Link Microchip Adapter
The J-Link Microchip Adapter converts the standard J-Link 20-pin 0.1 inch target connector to the Microchip RJ11 modular debug connector. Includes 6-pin RJ11 modular connector cable.
J-Link RX FINE Adapter (8.06.10)
Renesas RX FINE Adapter
The J-Link RX FINE Adapter converts the 20-pin, 0.1 inch standard connector to a 14-pin, 0.1 inch RX FINE connector. Includes the necessary cable.
J-Link Signal Smoothing Adapter (8.06.12)
Signal Smoothing Adapter
The J-Link Signal Smoothing Adapter can be inserted between the J-Link debug probe and the debug target to
overcome signal integrity issues.
J-Link Measurement+Patch Adapter (8.06.13)
J-Link Measurement+Patch Adapter
The J-Link Measurement+Patch Adapter provides test points for all
debug signals to allow easy access for test probes, and allows customized wiring between
J-Link and targets that do not provide a standard debug connector.
SEGGER Intel FPGA Adapter (8.06.15)
SEGGER Intel FPGA Adapter
The SEGGER Intel FPGA Adapter (formerly referred to as the J-Link Altera Adapter) converts the 20-pin, 0.1 inch pitch standard J-Link connector to a 10-pin Intel FPGA JTAG connector providing debug access to FPGA based MCU cores like the dual core ARM Cortex-A9 in the Cyclone V devices.
J-Link 6-pin Needle Adapter (8.06.16)
20-Pin to 6-Pin Needle Adapter
The 20-Pin to 6-Pin Needle Adapter converts the 20-pin, 0.1 inch standard connector to a 6-pin, 0.05 inch needle pattern.
J-Link Supply Adapter (8.06.14)
Supply Adapter
The J-Link Supply Adapter provides a fixed I/O voltage level for VTRef. It eliminates the need to connect VTRef (pin1 on the standard J-Link interface) to the target.
USB Isolator (8.07.02)
USB Electrical Isolator
The J-Link USB Isolator can be connected between the J-Link / Flasher and the host PC to provide electrical isolation.
J-Link Target Supply Adapter (8.06.18)
Target Supply Adapter
The J-Link Supply Adapter provides a default voltage of 3.3V to power the target using pin 19. The voltage can be adjusted by replacing resistors.
J-Link Xilinx Adapter (8.06.19)
Xilinx Adapter
The J-Link Xilinx Adapter converts the 20-pin, 0.1 inch pitch standard J-Link connector to a 14-pin 2mm pitch connector.
RL78 14-Pin Programming Adapter (8.06.20)
RL78 Programming Adapter
The RL78 Programming Adapter converts the 20-pin, 0.1 inch pitch standard J-Link connector to a 14-pin, E1 connector. Includes 14 pin ribbon cable.
J-Trace Isolator (8.07.10)
J-Trace Isolator
The J-Trace Isolator can be connected between a J-Trace PRO V2 or later and any ARM-board that uses the standard 19-pin Cortex-M connector to provide electrical isolation while keeping high speed trace capabilities.
J-Trace Mictor 38 Adapter (8.06.21)
J-Trace Mictor 38 Adapter
Adapts from 20-pin .05" Cortex trace connector to 38 pin Mictor connector. The pin out follows the single target connector pin out specification as defined in the ARM ETM Architecture Specification.
SEGGER SiFive-ARTY Adapter (8.06.24)
SEGGER SiFive-ARTY Adapter
The SEGGER SiFive-ARTY Adapter allows debug connections between J-Link and the ARTY board running SiFive RISC-V core bitstreams.
J-Link Microchip 2-Wire JTAG TDI Adapter (8.06.23)
J-Link Microchip 2-Wire JTAG TDI Adapter
The J-Link Microchip 2-Wire JTAG TDI Adapter allows debug connections between J-Link and target hardware which comes with Microchip IS208x series MCUs. It supports the Microchip 6-pin single row .1" connector.